Cold paint road marking comes ready to lay down the moment the pail cracks open. No waiting on kettles to hit temperature. No propane lines snaking across the job site. A spray wand, a roller frame, or a simple brush-whatever the crew has on hand-moves this material from container to asphalt without a pause for warmup. The instant wet film meets pavement, it seeps into the stone-and-tar fabric and latches on with a hold that refuses to budge under twisting tire stress or the day-in, day-out abrasion of passing axles. It skins over fast enough that cones get pulled while the crew still packs up. And through freeze-thaw cycles, blistering afternoons, and unfiltered sunlight, the cured stripe holds its ground-keeping edges sharp and messages readable far past the point where lesser coatings have given up.

Strong Adhesion

Excellent Weather Resistance

Good Wear Resistance

Fast Drying Speed

Low VOC Emissions

Specification

Color	White,Yellow other color could be customized
Density (g/cm)	1.7
VOC (g/kg)	262
Viscosity (η), s	149
Non-tire-sticking drying time (min)	11
Hiding power (%)	White: ≥95 Yellow: ≥80
Abrasive Resistance (mg)	51 (Weight loss after 200 cycles under 1000g load)
Adhesion (Circle-drawing method)	2 grade
Flexibility, mm	1
Solid content (%)	73.8
Package	25KG/Barrel with Pallets

APPLICATION

Racetrack & Equestrian Arena Rail Delineation

Harness racing tracks and equestrian arenas often feature compacted sand or crushed stone surfaces bordered by a narrow asphalt apron. Cold paint road marking provides a durable white or yellow edge line along this apron, helping riders and drivers gauge track limits at speed. The coating withstands kicked-up grit, hoof impacts near the rail, and periodic dragging or harrowing of the adjacent running surface.
Border Patrol Route & Remote Trail Kilometer Markers

Remote border patrol roads and unimproved access trails often lack permanent signage due to logistical difficulty and low traffic volume. Cold paint road marking can be air-dropped or transported in small quantities to mark kilometer posts, directional arrows, or hazard warnings directly onto existing compacted road surfaces. The paint cures independently of external power sources, requires no special equipment to apply, and provides essential navigational cues for patrol vehicles operating in areas with limited GPS reliability.
Emergency Shelter & Relief Supply Staging Grids

During disaster preparedness planning, municipalities designate large asphalt lots as emergency shelters or supply distribution hubs. Cold paint road marking enables advance stenciling of functional zones-triage areas, water station queues, generator placement squares-that lie dormant for months or years but must be instantly legible when activated. The markings endure seasonal weathering without disappearing, yet can be refreshed quickly with minimal equipment.

Product Highlights

Rich color options

White, yellow, red, blue, green, black.

Fast-drying and wear-resistant

It dries quickly and can be opened to traffic 10 minutes after construction. With reasonable construction technology, it can maintain its performance for over 6 months.

Strong adhesion

When sprayed on a dry, clean working surface (with guaranteed film thickness), no peeling will occur.

Vibrant and aesthetic

The color is bright and complies with industry standards, with no yellowing, discoloration or cracking. It has high brightness and strong visibility.

Easy construction

No special requirements for construction machinery; both spraying and manual brushing are applicable.

Night reflectivity

With a guaranteed film thickness and surface-sprinkled glass beads, it provides strong reflective effect at night.

Company Strength

01

30+ Years of Manufacturing Excellence

Three decades of expertise have made Mate Star a master in coating raw material selection and formula development-curating premium, durable raw materials and refining formulas through thousands of tests to ensure optimal adhesion, weather resistance, and compatibility with diverse substrates.
02

Complete Product Ecosystem

From strict raw material testing to rigorous finished product quality control-ensuring top-tier coatings are reliably delivered to clients every time.
03

Reliable, Certified Quality

Every product meets strict global certifications (ISO, CE, etc.)
04

Innovation-Driven Global Support

Blending cutting-edge R&D with a worldwide service network, we deliver advanced solutions paired with localized support to maximize client value globally.

Our Department

We have a professional team, including departments for production, technology, sales, and marketing.

VIEW ALL SERVICES

Production Department

Factory Manager: Overall production management & scheduling R&D/QC: Formula R&D & product quality inspection Operators: Production process operation

Technology Department

Technical Engineer: Responsible for construction plan design and technology development;
Technical Support: Responsible for on-site technical guidance and after-sales support.

Sales Department

The Sales Director is responsible for sales strategy and team management;
the Foreign Trade Manager is responsible for overseas market development and order follow-up.